Adhesive Bonding & Webbing

Odif 505 Temporary Fabric Adhesive is ideal for no pin basting of the quilting sandwich.

It avoids threading steps and the use of pins.

It is also used for temporary and precise holding of the fabric during sewing or machine embroidery.

It does not stain the fabric.

It evaporates when the fabric is handled and disappears when washed.

To Use:

• Protect work surface.
• Shake well before each use.
• For patchwork, Odif 505 Temporary Fabric Adhesive is ideal for assembling the quilt sandwich without basting:
• Spray at 10 inches, directly onto the batting.
• Position the quilt top and then turn your patchwork over.
• Spray again on the batting and position the backing fabric.
• For embroidery, place the stabilizer in the embroidery hoop.
• Spray the Odif 505 adhesive on the stabilizer and then adhere your fabric or garment without hooping.
• This method prevents hooping marks on the fabric.

Tip: To clean the embroidery hoop: wash with soapy water or use DK5 Odif.
In case of stains: dry clean.

HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning or basting. Just stitch right thru the adhered layers of fabric.

Product Details

• Heat-activated
• Permanent
• Double-sided adhesive
• For use on fabric
• Doesn’t gum up needles
• Proudly made in the USA

General Directions

• Pre-wash all materials without fabric softeners. Pretest adhesive on materials before starting the project.
• Preheat iron to medium heat, No steam. Place adhesive on the back of the material to be bonded (paper liner should face up).
• Place and hold the iron on the paper liner for 2 seconds. Repeat until the entire surface is bonded. Allow to cool.
• Cut to size or shape needed. Peel off the paper liner. 
• Place material, adhesive side down, on top of the project. Press and hold iron for
• 6 seconds on each section until the entire piece is bonded.
• The times listed above are for cotton. Iron thick fabrics an additional 2 seconds from the back of the project.
• Hand or Machine sew along edges.

Tips 

• If stitching is NOT desired, use HeatnBond Ultrahold in the red package.
• Do not touch iron directly to the adhesive sheet. Do not iron directly to your ironing board
• HeatnBond LITE sheets can be run thru an INKJET printer (NOT a laser jet or copy machine). Cut to printer size, feed into printer to print on the paper side, set printer to Draft or Transparency setting, allow to dry before touching. Run any lettering in mirror setting so they are the correct orientation when cut from the fabric.
• Must be sewn or otherwise attached before washing. Machine wash cold and dry on low heat or no heat (and in accordance with garment/fabric washing directions). Avoid repeated or excessive ironing to the area after fusing.

HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning or basting. Just stitch right thru the adhered layers of fabric.

Product Details

• Heat-activated
• Permanent
• Double-sided adhesive
• For use on fabric
• Doesn’t gum up needles
• Proudly made in the USA

General Directions

• Pre-wash all materials without fabric softeners. Pretest adhesive on materials before starting the project.
• Preheat iron to medium heat, No steam. Place adhesive on the back of the material to be bonded (paper liner should face up).
• Place and hold the iron on the paper liner for 2 seconds. Repeat until the entire surface is bonded. Allow to cool.
• Cut to size or shape needed. Peel off the paper liner. 
• Place material, adhesive side down, on top of the project. Press and hold iron for
• 6 seconds on each section until the entire piece is bonded.
• The times listed above are for cotton. Iron thick fabrics an additional 2 seconds from the back of the project.
• Hand or Machine sew along edges.

Tips 

• If stitching is NOT desired, use HeatnBond Ultrahold in the red package.
• Do not touch iron directly to the adhesive sheet. Do not iron directly to your ironing board
• HeatnBond LITE sheets can be run thru an INKJET printer (NOT a laser jet or copy machine). Cut to printer size, feed into printer to print on the paper side, set printer to Draft or Transparency setting, allow to dry before touching. Run any lettering in mirror setting so they are the correct orientation when cut from the fabric.
• Must be sewn or otherwise attached before washing. Machine wash cold and dry on low heat or no heat (and in accordance with garment/fabric washing directions). Avoid repeated or excessive ironing to the area after fusing.

HeatnBond Ultrahold is a roll of paper backed, iron-on, No Sew, double-sided adhesive for bonding fabric without the need for pinning. Ultrahold’s no-sew bond is stronger than traditional fusible webs. The solid sheet adhesive means edge to edge coverage for appliqué shapes on quilts, wall hangings and attire without puckering or bunching. Draw or print directly on the paper backing to easily design appliqué pieces!

Product Details

• 1 package; 17 inch width x 1 yard (43 cm x 91.4 cm)
• Heat activated
• Permanent
• Double-sided adhesive
• Solid sheet adhesive on a paper backing
• For use on fabric, but can be used with a wide range of materials such as foil, lame, felt , suede, cardboard, leather and wood.
• No Sewing needed
• Acid-Free 
• Proudly made in the USA

HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning or basting. Just stitch right thru the adhered layers of fabric.

Product Details

• Heat-activated
• Permanent
• Double-sided adhesive
• For use on fabric
• Doesn’t gum up needles
• Proudly made in the USA

General Directions

• Pre-wash all materials without fabric softeners. Pretest adhesive on materials before starting the project.
• Preheat iron to medium heat, No steam. Place adhesive on the back of the material to be bonded (paper liner should face up).
• Place and hold the iron on the paper liner for 2 seconds. Repeat until the entire surface is bonded. Allow to cool.
• Cut to size or shape needed. Peel off the paper liner. 
• Place material, adhesive side down, on top of the project. Press and hold iron for
• 6 seconds on each section until the entire piece is bonded.
• The times listed above are for cotton. Iron thick fabrics an additional 2 seconds from the back of the project.
• Hand or Machine sew along edges.

Tips 

• If stitching is NOT desired, use HeatnBond Ultrahold in the red package.
• Do not touch iron directly to the adhesive sheet. Do not iron directly to your ironing board
• HeatnBond LITE sheets can be run thru an INKJET printer (NOT a laser jet or copy machine). Cut to printer size, feed into printer to print on the paper side, set printer to Draft or Transparency setting, allow to dry before touching. Run any lettering in mirror setting so they are the correct orientation when cut from the fabric.
• Must be sewn or otherwise attached before washing. Machine wash cold and dry on low heat or no heat (and in accordance with garment/fabric washing directions). Avoid repeated or excessive ironing to the area after fusing.

HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning or basting. Just stitch right thru the adhered layers of fabric.

Product Details

• Heat-activated
• Permanent
• Double-sided adhesive
• For use on fabric
• Doesn’t gum up needles
• Proudly made in the USA

General Directions

• Pre-wash all materials without fabric softeners. Pretest adhesive on materials before starting the project.
• Preheat iron to medium heat, No steam. Place adhesive on the back of the material to be bonded (paper liner should face up).
• Place and hold the iron on the paper liner for 2 seconds. Repeat until the entire surface is bonded. Allow to cool.
• Cut to size or shape needed. Peel off the paper liner. 
• Place material, adhesive side down, on top of the project. Press and hold iron for
• 6 seconds on each section until the entire piece is bonded.
• The times listed above are for cotton. Iron thick fabrics an additional 2 seconds from the back of the project.
• Hand or Machine sew along edges.

Tips 

• If stitching is NOT desired, use HeatnBond Ultrahold in the red package.
• Do not touch iron directly to the adhesive sheet. Do not iron directly to your ironing board
• HeatnBond LITE sheets can be run thru an INKJET printer (NOT a laser jet or copy machine). Cut to printer size, feed into printer to print on the paper side, set printer to Draft or Transparency setting, allow to dry before touching. Run any lettering in mirror setting so they are the correct orientation when cut from the fabric.
• Must be sewn or otherwise attached before washing. Machine wash cold and dry on low heat or no heat (and in accordance with garment/fabric washing directions). Avoid repeated or excessive ironing to the area after fusing.

HeatnBond Lite is a roll of iron-on, sewable, double-sided adhesive for bonding fabric without extra weight or stiffness. Use it in place of pinning or basting. Just stitch right thru the adhered layers of fabric.

Product Details

• 5/8 in x 10 yards (16 mm x 9.1 m)
• Heat-activated
• Permanent
• Double-sided adhesive
• For use on fabric
• Doesn’t gum up needles
• Proudly made in the USA

General Directions

• Pre-wash all materials without fabric softeners. Pretest adhesive on materials before starting the project.
• Preheat iron to medium heat, No steam. Place adhesive on the back of the material to be bonded (paper liner should face up).
• Place and hold the iron on the paper liner for 2 seconds. Repeat until the entire surface is bonded. Allow to cool.
• Cut to size or shape needed. Peel off paper liner. 
• Place material, adhesive side down, on top of the project. Press and hold iron for
• 6 seconds on each section until the entire piece is bonded.
• The times listed above are for cotton. Iron thick fabrics an additional 2 seconds from the back of the project.
• Hand or Machine sew along edges.

Tips

• If stitching is NOT desired, use HeatnBond Ultrahold in the red package.
• Do not touch iron directly to the adhesive sheet. Do not iron directly to your ironing board
• HeatnBond LITE sheets can be run thru an INKJET printer (NOT a laser jet or copy machine). Cut to printer size, feed into printer to print on the paper side, set printer to Draft or Transparency setting, allow to dry before touching. Run any lettering in mirror setting so they are the correct orientation when cut from the fabric.
• Must be sewn or otherwise attached before washing. Machine wash cold and dry on low heat or no heat (and in accordance with garment/fabric washing directions). Avoid repeated or excessive ironing to the area after fusing.

Product Care

• Machine wash & dry finished projects without fabric softeners or dry clean.
• You may leave edges unfinished, but if you choose to sew through, make sure that the Steam-A-Seam 2® is fully fused with a steam iron – 30+ sec and let set before sewing.
• When laundering, avoid using fabric softener. Fabric softener chemicals erode the fusible web over time.

Lite Steam-a-Seam 2 ::  9" x 12" Sheets

Get Stuck on Fabric Fusing!
The #1 most loved brand of double stick fusible web, Steam-A-Seam 2 and Lite Steam-A-Seam 2 are back and better than ever making appliqué fun again!! Steam-A-Seam 2 and Lite Steam-A-Seam 2 are heat-activated pressure-sensitive fusible webs. This makes the web sticky and repositionable for easy placement of your appliqué giving you the ability to play with your design before permanently ironing.

You’ll never make a mistake – the last step is to fuse when everything is perfectly in its place! Before fusing, tack your project to a wall or try on a garment to check appliqué placement; you’re able to reposition pieces while you’re wearing them.

Lite Steam-A-Seam is the incomparable lightweight fusible web that bonds the same as Steam-A-Seam 2 but with 1/2 the weight – Perfect for laces, ribbon, silk, and chiffon!

Benefits of Using Lite Steam-A-Seam® vs other brands:

• Repositionable stick
• Bond is strong & permanent
• Leave edges unfinished – will not fray or lift
• Will not gum up your needle
• Machine wash and dry (See Product Care)
• So Easy to Use
• New grid paper aids in tracing
• Easy to see through and write on
• Printer-friendly!

Use Lite Steam-A-Seam 2 with different materials & projects:

• Appliqué
• No-Sew hems & seams
• Add or repair zippers, pockets, etc.
• Apply lace, ribbon & embellishments
• Durable enough to use with paper, cardboard, wood, glass, etc!

Product Care

Machine wash & dry finished projects without fabric softeners or dry clean.
You may leave edges unfinished, but if you choose to sew through, make sure that the Lite Steam-A-Seam 2 is fully fused with a steam iron – 30+ sec and let set before sewing.
When laundering, avoid using fabric softener. Fabric softener chemicals erode the fusible web over time.

Steam-a-Seam 2 ::  9" x 12" Sheets

Product Care

• Machine wash & dry finished projects without fabric softeners or dry clean.
• You may leave edges unfinished, but if you choose to sew through, make sure that the Steam-A-Seam 2 is fully fused with a steam iron – 30+ sec and let set before sewing.
• When laundering, avoid using fabric softener. Fabric softener chemicals erode the fusible web over time.

Steam-a-Seam 2 ::  1/4" x 40yds

Get Stuck on Lite Steam-A-Seam 2 and Steam-A-Seam 2 Fabric Fusing Tapes –
Perfect for Hems, Seams, and Adding Lace, Ribbon and Trim! 

Steam-A-Seam 2 and Lite Steam-A-Seam 2 are the most loved fusible webs on the market for many good reasons. The pressure-sensitive adhesive gives the web an unmatched tacky, repositionable value. This allows for perfect placement every time. When hemming up pants for example – go ahead and tack the hem in place and try on the pants before making anything permanent. The light tack of the adhesive will hold allowing you to get your hem perfect and ready to iron for a permanent bond. No pins are necessary! Simply finger press in place – no mistakes – the last step is to fuse when everything is perfect! Lite Steam-A-Seam 2 tapes and Steam-A-Seam 2 tapes work with all types of fabric. Add ribbon and trim to stretchy knits, use with sequins and beads and watch it disappear into lace with its washable and dry-cleanable permanent bond! They’re so easy to use with excellent results. See the tutorial below.

Use the 1/2″ and 1/4″ tapes for far more than hems and seams. The 1/2″ tape is ideal for getting zippers perfectly in place before sewing and that pocket is exactly where you want it before making it permanent. The 1/4″ tape is ideal for adding binding to quickly finish off quilts, placemats, wall hangings and so much more – no whip stitch needed! The 1/4″ tape makes sure your points are together when piecing your quilt top. Stick the points together and give them a quick fuse, then sew for perfect pinwheels every time!

Lite Steam-A-Seam 2 is half the weight of Steam-A-Seam 2 and you will use them both in the same way. It is best to use Lite Steam-A-Seam 2 with more delicate fabrics like sheer lamé, laces, and with clothing or even quilts. Lite Steam-A-Seam 2 is best for projects that will be close to the body for a flexible permanent bond. Heavy fabrics like denim and Ultra Suede work well with Steam-A-Seam 2 as do projects that will see a lot of wear like placemats, pot holders, towels.

Lite Steam-A-Seam 2 and Steam-A-Seam 2 tapes won’t gum your needle if you decide to sew. If you ever feel any resistance when sewing, stop sewing. It hasn’t been fused long enough. Remember how we talked about the pressure-sensitive adhesive that gives Steam-A-Seam 2 and Lite Steam-a-Seam 2 its temporary tackiness? Steam dissipates this tacky adhesive as it is not needed to fuse the fabrics together. The web itself is what permanently bonds the fabrics together. If there is resistance or gumming on your needle, using plenty of steam, go back over the project making sure to completely and thoroughly steam all areas. Don’t worry about overheating – Lite Steam-A-Seam 2 and Steam-A-Seam 2 can take the heat! When working with multiple layers fusing from the front and from the back of the project works well. Always allow the project to cool completely before sewing. If your needle got gummed up, a little rubbing alcohol will clean it right up.

Benefits of Using Steam-A-Seam®:

• Repositionable stick
• Bond is strong & permanent
• Leave edges unfinished – will not fray or lift
• Will not gum up your needle
• Machine wash and dry (See Product Care)
• So Easy to Use

Use Steam-A-Seam 2 with different materials & projects:

• Appliqué
• No-Sew hems & seams
• Add or repair zippers, pockets, etc.
• Apply lace, ribbon & embellishments
• Durable enough to use with paper, cardboard, wood, glass, etc!

Product Care

Machine wash & dry finished projects without fabric softeners or dry clean.
You may leave edges unfinished, but if you choose to sew through, make sure that the Steam-A-Seam 2® is fully fused with a steam iron – 30+ sec and let set before sewing.
When laundering, avoid using fabric softener. Fabric softener chemicals erode the fusible web over time.

Steam-a-Seam 2 ::  1/2" x 20yds

Get Stuck on Lite Steam-A-Seam 2 and Steam-A-Seam 2 Fabric Fusing Tapes –
Perfect for Hems, Seams, and Adding Lace, Ribbon and Trim! 

Steam-A-Seam 2 and Lite Steam-A-Seam 2 are the most loved fusible webs on the market for many good reasons. The pressure-sensitive adhesive gives the web an unmatched tacky, repositionable value. This allows for perfect placement every time. When hemming up pants for example – go ahead and tack the hem in place and try on the pants before making anything permanent. The light tack of the adhesive will hold allowing you to get your hem perfect and ready to iron for a permanent bond. No pins are necessary! Simply finger press in place – no mistakes – the last step is to fuse when everything is perfect! Lite Steam-A-Seam 2 tapes and Steam-A-Seam 2 tapes work with all types of fabric. Add ribbon and trim to stretchy knits, use with sequins and beads and watch it disappear into lace with its washable and dry-cleanable permanent bond! They’re so easy to use with excellent results. See the tutorial below.

Use the 1/2″ and 1/4″ tapes for far more than hems and seams. The 1/2″ tape is ideal for getting zippers perfectly in place before sewing and that pocket is exactly where you want it before making it permanent. The 1/4″ tape is ideal for adding binding to quickly finish off quilts, placemats, wall hangings and so much more – no whip stitch needed! The 1/4″ tape makes sure your points are together when piecing your quilt top. Stick the points together and give them a quick fuse, then sew for perfect pinwheels every time!

Lite Steam-A-Seam 2 is half the weight of Steam-A-Seam 2 and you will use them both in the same way. It is best to use Lite Steam-A-Seam 2 with more delicate fabrics like sheer lamé, laces, and with clothing or even quilts. Lite Steam-A-Seam 2 is best for projects that will be close to the body for a flexible permanent bond. Heavy fabrics like denim and Ultra Suede work well with Steam-A-Seam 2 as do projects that will see a lot of wear like placemats, pot holders, towels.

Lite Steam-A-Seam 2 and Steam-A-Seam 2 tapes won’t gum your needle if you decide to sew. If you ever feel any resistance when sewing, stop sewing. It hasn’t been fused long enough. Remember how we talked about the pressure-sensitive adhesive that gives Steam-A-Seam 2 and Lite Steam-a-Seam 2 its temporary tackiness? Steam dissipates this tacky adhesive as it is not needed to fuse the fabrics together. The web itself is what permanently bonds the fabrics together. If there is resistance or gumming on your needle, using plenty of steam, go back over the project making sure to completely and thoroughly steam all areas. Don’t worry about overheating – Lite Steam-A-Seam 2 and Steam-A-Seam 2 can take the heat! When working with multiple layers fusing from the front and from the back of the project works well. Always allow the project to cool completely before sewing. If your needle got gummed up, a little rubbing alcohol will clean it right up.

Benefits of Using Steam-A-Seam®:

• Repositionable stick
• Bond is strong & permanent
• Leave edges unfinished – will not fray or lift
• Will not gum up your needle
• Machine wash and dry (See Product Care)
• So Easy to Use

Use Steam-A-Seam 2 with different materials & projects:

• Appliqué
• No-Sew hems & seams
• Add or repair zippers, pockets, etc.
• Apply lace, ribbon & embellishments
• Durable enough to use with paper, cardboard, wood, glass, etc!

Product Care

Machine wash & dry finished projects without fabric softeners or dry clean.
You may leave edges unfinished, but if you choose to sew through, make sure that the Steam-A-Seam 2® is fully fused with a steam iron – 30+ sec and let set before sewing.
When laundering, avoid using fabric softener. Fabric softener chemicals erode the fusible web over time.